No. Use the monaural jack.

Possible causes include an input level that is too high and an output level that is too high.
Adjust the [TRIM] control (input) or the LEVEL control (output) so that +14 on the level meter does not light.

If the sound is distorted even when the input and output levels are adjusted, you may be exceeding the power amplifier’s maximum allowable input level. Lower the output level to an appropriate level using the [MASTER ATT] control on the rear panel.
The level is lowered to 50% at -6 dB, to 70% at -3 dB.
This setting is not associated with the master level meter.

MASTER OUT1 (XLR) and BOOTH (TRS) are balanced terminals.

Both a control cable and audio cable are required to use the fader start function.
Note that the fader start function may not work when only a digital audio cable and control cable are connected.
In this case, also connect an analog audio cable.
To use the fader start function with LINK connections, there is no need to connect an audio cable, but the CDJ-2000 or CDJ-900 must support LINK connections.
Check that the CDJ’s version is 3.00 or later.

When controls and buttons are operated, the corresponding MIDI signal is output to the computer via USB cable. (For details, see the operating instructions.) The signal assignment cannot be changed. Also, MIDI signal input is not supported.

We do not guarantee performance when using a converter cable (or converter plug). Connect the MASTER OUT1 terminals to an amplifier with an XLR input, the MASTER OUT2 terminal to an amplifier with an RCA input.

Connections can be made using the DIN terminal, but the key assignment function does not support the EFX-1000, so it cannot be operated.
With the DJM-2000, MIDI signals can be output to a computer using a USB cable.

The terminal is of the pre-insert type (input/output before the channel fader).

0 db.
This is switched according to the rated input level of the power amplifier or powered speakers used.

No.

Polarities as seen from the front, for both MIC

The signals are the same, but they are not affected by the MASTER VR.

Yes.
To use the fader start function with LINK connections to the CDJ-2000 or CDJ-900, the CDJ-2000 or CDJ-900 must support LINK connections.
Check that the CDJ’s version is 3.00 or later.

A CDJ-2000 or CDJ-900 supporting the LINK function.
To use the LINK function of the CDJ-2000 or CDJ-900, the CDJ-2000 or CDJ-900 must support LINK connections.
Check that the CDJ’s version is 3.00 or later.

Echo reverbs cannot be achieved if the SEND/RETURN effect is set to all channels. Set the effect channel to Master.

Yes, if the DVD player’s digital output signals are PCM signals. However, Dolby Digital and DTS signals cannot be input.

Yes.
The driver software is compatible with the following operating systems:
-Mac OS X (10.3.9 and later)
-Windows Vista® Home Basic/Home Premium/Ultimate/Business
-Windows® XP Home Edition/Professional (SP2 and later)
The driver software is not compatible with 64-bit operating systems (Windows® XP Professional x64 Edition and 64-bit editions of Windows Vista®).
Also, the computer’s recommended operating environment depends on the DJ application.
Be sure to check the recommended operating environment for the DJ application you are using.

Yes. TRS terminals are supported, so both stereo and monaural headphone cables can be used.

Yes, all you need is one USB cable.
The driver software must be installed beforehand.
When using applications of other brands, refer to the application’s operating instructions.

Yes. Set the sound setting on the computer to the DJM-2000.
Up to 4 sets of audio signals can be input to the DJM-2000 using an ASIO driver.

When the DJM-2000 is first connected to a computer or to a different USB port on the computer, the message "Installing device driver software" may appear. Wait until the message "Prepared to use device" is displayed.

When installing on Windows XP
-The message "Connect to Windows Update to search for hardware?" may appear during installation. Choose "No, not now.", then click "Next"to proceed with installation.
-The message "Choose the installation method" may appear during installation. Choose "Install software automatically (recommended)", then click "Next"to proceed with installation.
-The "Windows Security" window may appear during installation. Click "Install this driver software." to proceed with installation.

TIP = HOT, RING = COLD, SLEEVE = GND.

No. The supported operating systems are as follows:
-Windows Vista® Home Basic/ Home Premium/ Ultimate/ Business
-Windows® XP Home Edition/ Professional (SP2 or later)
The driver software is not supported on 64-bit versions of operating systems (Windows® XP Professional x64 Edition and 64-bit editions of Windows Vista®).

Is the CDJ-2000 or CDJ-900 connected to the PC1 or PC2 terminal?
When a player is connected to the PC1 or PC2 terminal and has the same player number as the CDJ, the player connected last cannot be recognized, a message is displayed and the channel number flashes.
Connect the CDJ-2000 or CDJ-900 to the LINK 1, 2, 3 or 4 terminal.

The CDJ version must be updated (to Ver. 3.00 or later).

With this mixer, the IP address is assigned automatically by the Auto IP or DHCP function. The computer must also be set so that the IP address is assigned automatically. Anywhere from 30 seconds to 1 minute is required from the time LAN recognition begins until the IP addresses are set, though this depends on the computer’s operating system.