DDJ-SZ2

Q1 Is there a correct order for connecting the USB cable of DDJ-SZ2 and starting up Serato DJ? Can either be done first?: A1

Either can be done first.

Net Number : 2
Q2 Tell me about the conditions for players that can be used in combination with this unit.: A2

The players must be turntables (analog players) that can play analog records or CDJ players that can play music CDs (CD-DA). In both cases, check that they are equipped with audio output terminals.

Net Number : 26
Q3 What type of amplifier should be connected to produce sound?: A3

This unit is equipped with two sets of analog MASTER outputs (audio outputs).
By connecting these audio outputs to the external inputs of a general amplifier, mini component system, or powered speakers, sound can be output to speakers through an external amplifier. Connect this unit's MASTER OUT 1 terminals to an amplifier with XLR input and the MASTER OUT 2 terminals to an amplifier with RCA input.

Net Number : 27
Q4 Can this unit's MASTER OUT 1 terminals be connected to an amplifier's RCA inputs using an XLR-RCA converter cable (converter plug)? Also, can this unit's MASTER OUT 2 terminals be connected to an amplifier's XLR inputs using an RCA-XLR converter cable (converter plug)?: A4

Performance is not guaranteed via a converter cable (converter plug).
Connect the MASTER OUT 1 terminals and BOOTH OUT terminals to an amplifier with XLR input and the MASTER OUT 2 terminals to an amplifier with RCA input.

Net Number : 28
Q5 Are there terminals that support the balanced type?: A5

The following terminals support the balanced type.

-MASTER OUT 1 terminals (XLR)
-BOOTH OUT terminals (TRS)
-MIC1 jack (XLR/TRS）
-MIC2 jack (TRS）

Net Number : 29
Q6 Which type is the microphone (MIC) jack, balanced or unbalanced? If it is the balanced type, what are its polarities?: A6

It is a balanced terminal.
For its polarities as seen from the front of the terminal, see the diagram.

Net Number : 30
Q7 Does the microphone (MIC) jack support phantom power supplies?: A7

No, it does not.

Net Number : 31
Q8 Can I use a stereo microphone?: A8

Stereo microphones are not supported. Use a monaural microphone.

Net Number : 32
Q9 Do the BOOTH OUT terminals support a 3-pin (TRS) phone jack?: A9

Yes, they do.
Stereo and monaural phone jacks can be connected.

Net Number : 33
Q10 The BOOTH OUT terminals are 3-pin (TRS) phone jacks. What are the polarities when using them as balanced terminals?: A10

TIP=HOT, RING=COLD, and SLEEVE=GND

Net Number : 34
Q11 What is the Kensington security slot used for?: A11

The slot is used to attach an anti-theft wire lock.

Net Number : 35
Q12 What is driver software?: A12

Driver software allows you to connect this unit to a computer.
The driver software can be obtained from the support site of the Pioneer DJ web support page.

Net Number : 68
Q13 Is it necessary to install the driver software using Mac OS X?: A13

Yes. See "Installing the software" on page 4 of the operating instructions to install the driver software.

Net Number : 72
Q14 Are balanced terminals available?: A14

The [MASTER OUT1] terminals are balanced output terminals. Use XLR terminals.

Net Number : 75
Q15 Is an Internet environment (connection) required?: A15

An Internet connection environment is necessary to download the Serato DJ software and to upgrade it to the latest version.

Net Number : 76
Q16 What do I need other than the DDJ-SZ2 to hold DJ performances?: A16

To use DDJ-SZ2 as a controller, the following equipment items are required in addition to DDJ-SZ2.

　When using DDJ-SZ2 as a controller
　　-Computer on which Serato DJ is installed
　　-Powered speakers
　　-Headphones

Net Number : 77
Q17 Can this unit be used with the computer's bus power only?: A17

This unit cannot be used with the USB bus power. Connect the unit to a power outlet using the included power cord.

Net Number : 79
Q18 Is a sound card required separately?: A18

A sound card does not need to purchased separately because this unit has a built-in sound card.

Net Number : 96
Q19 Are balanced terminals available?: A19

The MASTER OUT1 (XLR) and BOOTH (TRS) terminals are balanced terminals.

Net Number : 98
Q20 Can I connect the unit to a PC/Mac that only has a USB Type-C port?: A20

If you're using a PC/Mac that only has a USB Type-C port, you'll need a USB Type-C (plug) to USB Type-A (socket) conversion cable (sold separately).
When using one of these cables, be sure it's a product recommended by the manufacturer of your PC/Mac.

Net Number : 112
Q21 Can I connect the unit to a PC/Mac via a USB hub?: A21

You should connect the unit directly to a USB port on the PC/Mac.
Connecting via a USB hub may cause unwanted noise or malfunction.
If you have to use a USB hub due to a limited number of USB ports on your PC/Mac, be sure to use a product recommended by the manufacturer of your PC/Mac.

Net Number : 113

FAQ Search